MAXTECH CORPORATION CL-144S (SF-114HV) Card Type Modem/Fax card Chip Set Unidentified I/O Options Line out (RJ-11), line in (RJ-11), microphone in, speaker out Maximum Modem Rate 14.4Kbps Maximum Fax Rate 14.4Kbps Data Modulation Protocol Bell 103/212A ITU-T V.32bis, V.32, V.22bis, V.22, V.21 Fax Modulation Protocol ITU-T V.17, V.27ter, V.29, V.21 Error Correction/Compression MNP5, V.42, V.42bis Fax Class Class I Data Bus 8-bit ISA [Image] CONNECTIONS Function Label Function Label RJ-11 line out CN1 Microphone in CN3 RJ-11 line in CN2 Speaker out CN4 SERIAL PORT ADDRESS Setting JP1/A JP1/B COM1 (3F8h) Closed Closed COM2 (2F8h) Open Closed COM3 (3E8h) Closed Open COM4 (2E8h) Open Open INTERRUPT Setting JP1/C JP1/D JP1/E JP1/F IR/FONT> Closed Open Open Open IRQ3 Open Closed Open Open IRQ4 Open Open Closed Open IRQ5 Open Open Open Closed SUPPORTED COMMAND SET Basic AT Commands AT, +++, A/ A, B, E, H, M, O, P, Q, T, V, X, Y, Z &C, &F, &G, &T, &V, &W, &Y, &Z Extended AT Commands \A, \B, \C, \G, \J, \K, \O, \U, \X, \Y, \Z %A, %E, %G -J "H S Registers S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S25, S26, S27, S30, S90, S108, S109 Note: See MHI Help File for full command documentation. PROPRIETARY AT COMMAND SET AUTO-MODE DETECTION Type: Configuration Format: AT [cmds] Nn [cmds] Description: Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. Command Function N0 Auto-mode detection disabled. Connect only at DTE rate N1 Automatic rate negotiation enabled COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Mn [cmds] Description: Selects communications mode Command Mode &M0 Asynchronous mode DATA SET READY (DSR) Type: Configuration Format: AT [cmds] &Sn [cmds] Description: Selects DSR options Command Function &S0 DSR forced high &S1 DSR high only while modem is handshaking or connected DATA TERMINAL READY (DTR) Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Selects modem response to DTR Command Function &D0 DTR override &D1 DTR toggle causes online command mode &D2 Normal DTR operations &D3 Resets on receipt of DTR DIAL Type: Immediate Format: AT [cmds] D<#> [cmds] Description: Dials telephone number according to any modifiers included in the string Note: Any combination of modifiers can be used to produce the desired dial functions in sequence. Command Function DP Pulse dialing enabled DR Answer mode enabled; originate mode disabled following handshake initiation. DS=n Dial stored telephone number n DT Tone dialing enabled/Pulse dialing disabled DW Dialing resumed following dial tone detection D, Dialing paused for amount of time specified in S8 register D! Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. D@ Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. PULSE DIALING RATIO Type: Configuration Format: AT [cmds] &Pn [cmds] Description: Selects pulse dial make/break ratio Command Function &P0 39/61ms at 10pps (North America) &P1 33/67ms at 10pps (Europe) REPORT INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested Command Function I0 Reports four digit product code I1 Reports ROM checksum I2 Reports internal memory test I3 Reports firmware ID I4 Reports internal ID SPEAKER VOLUME Type: Configuration Format: AT [cmds] Ln [cmds] Description: Controls speaker volume Command Function L0 Low volume setting L1 Low volume setting L2 Medium volume setting L3 Highest volume setting TRELLIS CODING Type: Configuration Format: AT [cmds] &Un [cmds] Description: Enables/disables trellis coding Command Function &U0 V.32 trellis coding enabled &U1 V.32 trellis coding disabled EXTENDED AT COMMAND SET COMPRESSION Type: Configuration Format: AT [cmds] %Cn [cmds] Description: Selects data compression Command Function %C0 Data compression disabled %C1 MNP5 enabled CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Description: Controls the type of connection the modem will operate in Command Function \N0 Normal mode enabled \N1 Direct mode enabled \N2 MNP mode enabled \N3 V.42, MNP or Normal mode enabled \N4 V.42 mode enabled EXTENDED RESULT CODES Type: Configuration Format: AT [cmds] \Vn [cmds] Description: Selects extended result codes Command Function \V0 Extended result codes disabled \V1 Send extended response set 1 \V2 Send extended response set 2 FLOW CONTROL TYPE Type: Configuration Format: AT [cmds] \Qn [cmds] Description: Sets type of flow control used by modem Command Function \Q0 Flow control disabled \Q1 Bi-directional XON/XOFF flow control enabled \Q2 CTS flow control by DCE enabled \Q3 Bi-directional RTS/CTS flow control enabled INACTIVITY TIMER Type: Configuration Format: AT [cmds] \Tn [cmds] Range: 0-90 Unit: 1 second Description: Sets the length of time that the modem does not receive information before it disconnects. V.42bis - MAXIMUM STRING LENGTH Type: Immediate Format: AT [cmds] "On [cmds] Range: 6-250 Unit: Characters Description: Selects string size for V.42bis compression